turbine ID:
690C
Showing 33 Kits in this category (of total 81 kits)
Kit ID: 50
To provide replacement parts and instructions for the installation of rudder pedal and control column boots in aircraft pressurized to the floor. It is recommended that CK184 be installed concurrently with this custom kit if the plugs on the rudder pedals and linkages are worn, damaged and incapable of providing a good seal, or if the plugs are too low or high to properly position boots.
Kit ID: 94
Provides added safety feature of alternate static source for flight instruments for all prop driven Models except 520, 560, 720.
Kit ID: 110
Provides a fuel low level warning system for the earlier Commander Models except 680T, 680V, 680W, 681.
Kit ID: 132
An extended range fuel system modification that increases usable fuel capacity from 425 gallons to 474 gallons for a range increase of approximately 240 nautical miles. Models 690C, 695.
Kit ID: 133
Modification utilizes conditioned air to prevent pilot and copilot side window from fogging. It also provides pilot and copilot removable inner windows which eliminate cold air on the crew?s shoulder. Models 690A, 690B, 690C, 695.
Kit ID: 134
Provides improved efficiency of Environmental Control Unit (ECU) by ducting only outside air across heat exchanger. Models 690C, 695.
Kit ID: 135
Provides a fully automatic airspeed monitoring system, which, because of the low drag feature that allows the Commander jet props to easily increase airspeed during let down, has introduced the added safety feature of an aural warning in the event of an inadvertent overspeed of the airplane. The sensing switch is pre-set to aurally alert the pilot of airspeeds exceeding 243 KIAS. Models 690, 690A, 690B, 690C, 695.
Kit ID: 136
Provides individual strobe light and individual tail light that is more economical to maintain with longer rated bulb life. Models 690B, 690C, 690D, 695, 695A.
Kit ID: 137
Eliminates internal fogging of windshields and subsequent moisture problems. The gold-tinted heat film also acts as a sunscreen. Models 690, 690A, 690B, 690C, 690D, 695, 695A, 695B.
Kit ID: 138
Kit ID: 140
Modification to replace your electro-hydraulic nose wheel steering system with a brake-pedal actuated hydraulic nose steering system. Models 690C, 690D, 695A, 695B.
Kit ID: 141
Provides an alternative air conditioning system for Models 690C and 695.
Kit ID: 148
Not a Custom Kit but an STC
Kit ID: 158
Provides an approved installation for the addition of inboard de-ice boots for the Models 690, 690A, 690B, 690C, and 695.
Kit ID: 159B
Provides approved modifications for nose gear and nose gear support structure problems caused by wear, overload conditions, prior AC-43.13 repairs, etc., for all Models.
Kit ID: 162C
Provides approved kits for repair of the lower fuselage stringers and lower floor keel beam caps for Models 500, 500A, 500B, 500S, 500U, 520, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FLP, 680FP, 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 695 and 720. Kits may be ordered based on extent of damage.
Kit ID: 163
Provides an approved procedure for installed windshields for the addition or repair of hump seals as the primary weather seal between the glass and fiberglass strap for the Models 690, 690A, 690B, 690C, 690D, 695, 695A, and 695B.
Kit ID: 164
Provides an approved repair for skin wrinkles / buckles located between fuselage stations 234.00 and 239.15 aft of the lower aft corner of the baggage door for Models 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, and 695. This kit adds an external skin doubler in the damaged area.
Kit ID: 167
Provides Models 500S (SN 3076 thru 3323 only) 680T, 680V, 680W, 681, 690A, 690B, 690C, 690D, 695, 695A, and 695B with a later production standard single-piece tail cone. Also allows for the replacement of the ?Stinger? tail cone for Models 690A and 690B.
Kit ID: 175A
Provides an easy-to-install vertical stabilizer lower rib replacement part and an Alternate Means of Compliance for Service Bulletin 218 (AD 95-13-02) for Models 500, 500A, 500B, 500S, 500U, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A and 720.
Kit ID: 177
Provides longer replacement seat tracks for the pilot and co-pilot seats allowing the seats to slide farther aft, giving better access while on the ground. Models 690, 690A, 690B, 690C, and 695.
Kit ID: 181
Modification designed to repair and replace damage to surrounding skin and attachment structure of the tail tie-down bumper. The modification also improves the attachment of the bumper support to F.S. (429.477 long fuselage) or (355.477 short fuselage) frames. Models 500, 500A, 500B, 500S, 500U, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A, 695B.
Kit ID: 183F
Provides an approved, alternative Environmental Control System. Note The -553 kit allows for upgrading an existing ENVIRO installation to the new Temperature & Flow control modules & Flow sensor. For all serial numbers for Models 690C, 690D, 695, 695A, 695B, & also for all serial numbers that have not previously complied with earlier modification to Gulfstream Dwg 880718 (Environmental system installation). For conversion from Sundstrand to Enviro, bleed air only.
Kit ID: 184
To provide rudder pedal installation for all serial numbers for Models 680, 680FP, 681, 680T, 685, 690, 690A, 690B, 690C, 695
Kit ID: 186
To provide approval and instruction for the replacement of Weldon Fuel Pumps with Parker Airborne Div. Fuel Pumps …for Models 690C, 690D, 695, and 695A
Kit ID: 187
MAIN LANDING GEAR LINKAGE KIT This kit provides an approved main landing gear door torque tube mod. This is a design improvement for models 680W, 680T, 680V, 681, 690, 690A/B/C/D, 695, 695A/B.
Kit ID: 188
This kit provides approval and instruction for the addition of the oxygen fill port for airplanes not equipped with such.
Kit ID: 189
Repeated removal and reinstallation of the center fuel cell and liner system leads to damage to the parts and oversized assembly holes. This kit provides approved installation of reusable fasteners for assembly of the fuel cell liner system. For Models: 560A/E/F, 680, 680FL/FL(P)/F(P), 680T/V/W, 720, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A, 695B
Kit ID: 190B
Replacement of fluorescent overhead cabin lights with low voltage LED (light emitting diode) lights reduces the overall electrical load and eliminates the need for the power supply which converts the 28 VDC of the aircraft to the 120 VAC required by the fluorescent lights. In addition, the life and brightness of the LED lights is significantly greater than that of the fluorescents. For Models: 690A, 690B, 690C, 690C, 690D, 695, 695A, 695B
Kit ID: 191
To provide approval and instruction for long seat rails on the left side for passenger convenience. For Models: 680FL, 680T, 680W, 681, 685, 690, 690A, 690B, 690C, and 695.
Kit ID: 200
The Dorsal of the original design (410080-3, -1 installation does not allow dispersion of moisture that builds up in the cavity between the Dorsal and the fuselage, which leads to corrosion on the fuselage under the Dorsal. This kit includes a replacement Dorsal that provides channels for moisture to drain out of the cavity, and is for replacement of a previously installed 410080 Dorsal. Models 690C/D, 695, 695A all.
Kit ID: 203
This kit provides instructions for replacement of 850626-503 and 850633-503 Transmitters Models 690C/D, 695, 695A 695B all.
Kit ID: 205
This kit provides instructions for replacement of the 750080-1 & ES10119 spacer, which is a two piece unit.