piston ID:
500S
Showing 17 Kits in this category (of total 81 kits)
Kit ID: 82A
Provides night flying safety feature by illuminating wing leading edge. Models 500A, 500B, 500S, 500U, 560F, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, and 681.
Kit ID: 87A
Easily installed kit, cap interchangeable with present cap. Fuel tank remains sealed even if cap is not secure. Models 500, 500A, 500B, 500S, 500U, 520, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P).
Kit ID: 94
Provides added safety feature of alternate static source for flight instruments for all prop driven Models except 520, 560, 720.
Kit ID: 97
Modification approved for ?All-Weather? flight conditions with new visual speed control indicator and ?Tellite? switch installations for Models 500A, 500B, 500U, 560F, 680F, 680FL, 680FL(P), 680F(P), 680T.
Kit ID: 109A
Modification features lower engine RPM charging capabilities, improved system reliability, and sufficient amperage output to assume additional electrical loads that may be imposed on the systems of Models 500B, 500S, 500U.
Kit ID: 110
Provides a fuel low level warning system for the earlier Commander Models except 680T, 680V, 680W, 681.
Kit ID: 116A
Modification provides an improved oil separator for better air oil separation for aircraft equipped with pneumatic operated equipment. Models 500B, 500S, 500U, 560F, 680F, 680FL, 680FL(P), 680F(P) equipped with H-14 Autopilot and/or deicing boots.
Kit ID: 145
To provide a main spar lower cap in these models. The main spar lower cap is a one piece extrusion that extends from W.S. 145.0 left to 145.0 right. Spar caps inspected per the requirements of Twin Commander Service Bulletin No. 208 which are not airworthy may be replaced per this Custom Kit. Spar caps with excessive damage or cracks may be replaced per this Custom Kit.
Kit ID: 151b
Provides an approved recognition light installation to increase the visibility of the airplane during flight for the Models 500S, s/n 3076 and later, 680W, s/n 1726 thru 1850, 681, 685, 690, 690A, and 690B, all serial numbers. Two kits are available--one with a pulsing function and one without.
Kit ID: 159B
Provides approved modifications for nose gear and nose gear support structure problems caused by wear, overload conditions, prior AC-43.13 repairs, etc., for all Models.
Kit ID: 162C
Provides approved kits for repair of the lower fuselage stringers and lower floor keel beam caps for Models 500, 500A, 500B, 500S, 500U, 520, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FLP, 680FP, 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 695 and 720. Kits may be ordered based on extent of damage.
Kit ID: 167
Provides Models 500S (SN 3076 thru 3323 only) 680T, 680V, 680W, 681, 690A, 690B, 690C, 690D, 695, 695A, and 695B with a later production standard single-piece tail cone. Also allows for the replacement of the ?Stinger? tail cone for Models 690A and 690B.
Kit ID: 175A
Provides an easy-to-install vertical stabilizer lower rib replacement part and an Alternate Means of Compliance for Service Bulletin 218 (AD 95-13-02) for Models 500, 500A, 500B, 500S, 500U, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A and 720.
Kit ID: 181
Modification designed to repair and replace damage to surrounding skin and attachment structure of the tail tie-down bumper. The modification also improves the attachment of the bumper support to F.S. (429.477 long fuselage) or (355.477 short fuselage) frames. Models 500, 500A, 500B, 500S, 500U, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A, 695B.
Kit ID: 182J
Provides an approved nose cone mounted landing light installation which increases the visibility of the airplane during landing and have no restrictions regarding when they can be activated during flight. The latest revision includes improved reflector design and replacement ballast. Models 500S, 680W, 681, 685, 690, 690A, 690B.
Kit ID: 204
This kit provides instructions for replacement of 53514-3 and 53534-103 Horns, which are no longer available.
Kit ID: 205
This kit provides instructions for replacement of the 750080-1 & ES10119 spacer, which is a two piece unit.
